HOME | DD

404bot — Lt-38

#38 #model #modelling #panzerkampfwagen #paper #papercraft #praga #tank #ww2 #pzkpfw
Published: 2014-11-22 17:19:16 +0000 UTC; Views: 3167; Favourites: 21; Downloads: 24
Redirect to original
Description This is my summer vacation's free time, forged into papermodel-rescaled down to 1:48 
Two incontinuous weeks wasted, thanks mostly to tracks, wheels and MG's paid extra attention to details- like glazing periscopes.

Short story shorter:
Wehrmacht's common policy was the use of foreign (often captured) weapons in their arsenal. Among the most prized trophies from early WW2 stage was two Czechoslovak light tanks Praga-produced LT-38 and Skoda LT-35 (latter  got cancelled in favor of LT-38).  
It was adopted after occupation of Czechoslovakia and named Pzkpfw-38(T). Crew faved them due to their reliable construction and great suspension system, and this tank proved it's good value in French campaign. However, as war goes on,insufficient  riveted armored protection and main gun firepower became obsolete (especially after inital encounters with Soviet T-34), but the chassis and suspension served as basis for numerous weapon platforms until final stages of war, Marder III and Hetzer SPG among them.

Stay tuned for more
Related content
Comments: 19

Siveir [2015-02-11 13:01:08 +0000 UTC]

I like the way it looks, like it's really metal-made!

👍: 0 ⏩: 1

404bot In reply to Siveir [2015-02-11 16:38:06 +0000 UTC]

Mockrát díky. Minulé léto jsem ho viděl u Lešanech , a hrozně se mi zalíbil. 
Doufám, že jednoho dne  snad udělám i "Škodováckýho bráchu" LT-35 nebo Mardera.  
P.S.: - takové kvalitní muzeum a vstupné zadáčo- smekám klobouk holt, vy se máte.

👍: 0 ⏩: 1

Siveir In reply to 404bot [2015-02-11 16:43:50 +0000 UTC]

Není zač, jen směle do další práce, stojí za to

Hm, to se tam budu muset zajet podívat... byť to mám krapet z ruky

👍: 0 ⏩: 1

404bot In reply to Siveir [2015-02-12 17:53:42 +0000 UTC]

Jasan, jenom musím ještě podokončovat pár jinejch věcí.
Vřele doporučuji, já jsem ujel ne míň než 600 km jenom tam, a z mýho pohledu to rozhodně stálo za to. Pro každýho fajnšmekra historie nebo techniky něco jako nutnost Někdy v létě pořádají i dynamickou ukázku, neneštěstí posledně jsem to minul o týden, doufám že letos to vyjde. 

👍: 0 ⏩: 1

Siveir In reply to 404bot [2015-02-12 19:05:25 +0000 UTC]

Uvidíme, jestli dcera dovolí, je docela náročná, a to je jí jenom pár měsíců. Ale díky za tip!

👍: 0 ⏩: 0

Baryonyx62 [2015-01-23 21:02:24 +0000 UTC]

Great job! Loving all the details! What did you use for edging?

👍: 0 ⏩: 1

404bot In reply to Baryonyx62 [2015-01-23 23:35:08 +0000 UTC]

Thanks a bunches
Using two tools: a worn-out ball point pen in bigger parts-like hull plates or glue tabs (allows scoring thicker papers, usually up to 190g/sq.m)

In smaller details prefer my custom tool made by duraluminium sheet ( 1mm thick/ 10mm wide,100mm long. Working end is in V-shape in approx. 20-deg.angle, sharpened on tip, but dull enough not to cut into paper. Grip is made by simply wrapping 'round electroinsulating duct-tape thick enough to prevent hand fatigue. Basically it is a dull scalpel made of hardened aluminuim).  I'm naturally applying much less pressure while edging w/ this one.

Hope it's helpful

👍: 0 ⏩: 1

Baryonyx62 In reply to 404bot [2015-01-24 00:06:33 +0000 UTC]

Oh sounds complicated but probably works well.

👍: 0 ⏩: 1

404bot In reply to Baryonyx62 [2015-01-24 09:02:15 +0000 UTC]

Like two minutes with angle grinder .Easy-peasy, lemon-squeazy  

Tell you my most-valuable hint: I ALWAYS pre-spray every printed paper with aerosol clear varnish before the build. (print-side understandably.) Only light coat, no need to soak-up the paper with varnish, one spray can lasts in my case for hundered pages, possibly more.
The print-color is far more durable, bent edges are less prone to raise "hair", and occasional glue offset is easy to wipe off, leaving no stains if done promptly  )

See for yourself

👍: 0 ⏩: 0

GeorgeEmpy [2014-11-23 12:07:37 +0000 UTC]

Hmm i have draw it week ago...

👍: 0 ⏩: 1

404bot In reply to GeorgeEmpy [2014-11-24 17:18:06 +0000 UTC]

Jasan, udelals  hezky obrazek hezkeho tanku.

👍: 0 ⏩: 1

GeorgeEmpy In reply to 404bot [2014-11-25 12:59:03 +0000 UTC]

Fakt?

👍: 0 ⏩: 1

404bot In reply to GeorgeEmpy [2014-11-25 13:08:27 +0000 UTC]

Jasne, Z casu na cas muzes pridat nejake dalsi nove obrazky

👍: 0 ⏩: 1

GeorgeEmpy In reply to 404bot [2014-11-25 13:12:30 +0000 UTC]

Plánuji nakreslit Tatru OA Vz.30. Co se týče toho tanku, příště si budu muset dát pozor na perspektivu, ta kola vypadají docela tence a jsou daleko od sebe. Věž je trochu delší a moc vzadu nad motorem. 

👍: 0 ⏩: 1

404bot In reply to GeorgeEmpy [2014-11-25 13:22:07 +0000 UTC]

To je ta sestikolka,jo? 
Neva, clovek se uci nejlepe na vlastnich chybach, co ja jsem se jich nadelal
Tak at se ti zadari

👍: 0 ⏩: 1

GeorgeEmpy In reply to 404bot [2014-11-25 13:28:00 +0000 UTC]

A díky.

👍: 0 ⏩: 0

DingoPatagonico [2014-11-22 19:28:36 +0000 UTC]

!! x3

👍: 0 ⏩: 0

E350tb [2014-11-22 17:25:43 +0000 UTC]

I love this tank. Much better then the Panzer II was.

Excellent work!

👍: 0 ⏩: 1

404bot In reply to E350tb [2014-11-22 17:30:55 +0000 UTC]

Thanks!

👍: 0 ⏩: 0