HOME | DD
Neffertity — $COM Mini Ethereal Goddess Sculpture
Published: 2012-09-26 17:02:16 +0000 UTC; Views: 1849; Favourites: 35; Downloads: 33
Redirect to original
Description
Here is the mini dragon sculpture commission for of her OC Ethereal Goddess.In celebration of your birthday I added scales to the entire sculpture.
Now to boast.
I was really faced with a challenge with her design. Primarily her wings and jewelry. But overall I'm quite pleased with how she turned out. ^_^ I used real Sworvoski Crystals in her accessories so they shine like real precious stones. 
And in her reference, I also saw that her chest plates and wings were EXTREMELY SPARKLEY, so I used this crystal powder stuff I've had for years and almost never get to use, and VWALA!!! Sparkley!!!
Well, she's been packed and shipped off as of today, so she should arrive within 3 - 5 buisiness days. ^_^ I hope you like her!
Sculpture Work is © ME
All made by hand
Time Taken: Roughly 56 hours
Materials Used:
-Sculpey Original & Super Sculpey Firm (Gray)
-Acryllic Paints
-Sworovski Crystals
-Liquid Sculpey
-Masking Tape
-Electrical wire & Beading Wire
Character is © *EG5
Like this sculpture? Want one like it? Then commission me! I do custom sculpture commissions starting at just $9.95!
Related content
Comments: 31
I'm very curious how did you make the membranes^^ I'm a newbie in sculpting
👍: 0 ⏩: 1
Normally, I use fabric. But on this one, I used Liquid Sculpey.
👍: 0 ⏩: 1
Thanks, she didn't come out quite like I had wanted though. Primarily her wings.
👍: 0 ⏩: 1
no prob and yeah i think i can see what ya mean
👍: 0 ⏩: 0
EEEEEK! jkljshfgkjsnvgklzjd
I... I... I...
I just can't wait to receive that gorgeousness in my own hands!!
And those scales... those jewels... all THAT sparkle...
I can see you really worked very hard on her! Thank you so much!!
PS: I little question, though. The wires used for her wings, they are VERY resistant, right? They won't break easily? Hope those wings aren't too heavy for them wires. x.x
👍: 0 ⏩: 1
I'm so happy you like her!
And yes, I use a very special type of wire that has a copper and rubber wax coating. If it does break, you'd have to have cut it. ^_^ The only likely issue I could see arising would be if the wire came out of the arm socket. Sometimes overbending it can pull it out.
That's an easy fix. Just dab a little bit of superglue onto the end of the wire that came out, and slide it back into the hole. ^_^
👍: 0 ⏩: 1
Ok, good to know! Not that I'm going to over bend her wings. I just wanted to make sure her wires are strong.
👍: 0 ⏩: 1
They are.
👍: 0 ⏩: 1
Now that sounds really interesting! I might request another sculpture in the near future again.
👍: 0 ⏩: 1
Perhaps I was blind before, but I don't remember seeing wires on your finished sculptures before. Did you use any other method of adding wings here?
👍: 0 ⏩: 1
There are wires on all the minis. and all the large ones too.
Since this character had gold jewelery, I made her wires gold to match, since I don't have white.
👍: 0 ⏩: 1
Yay, that's what I was aiming for.
👍: 0 ⏩: 1
